신뢰성 시험 & 기술지원 전문 업체 (주)이노테스는 언제나 고객사와 함께합니다.
| 구분 | 세부내용 | |
|---|---|---|
| 먼지시험 [Dust test] |
Test Standards according to customer request method Test method : According to customer specification |
 |
| 온습도시험 [Climate sequence test] |
Test Standards IEC 60068-2-38 Z/AD Test method ① Test temperature : as Profile ② Test cycle : 00 h, 00 cycles |
 |
| 열충격시험 [Thermal shocks pre-aging test] |
Test Standards IEC 60068-2-14 Na Test method ① Test temperature : Tmax 85℃, Tmin -40 ℃ ② No. of test cycle : 20 ③ Transition time : within 30s (2 zone elevation type) |
 |
| 온도측정시험 [Temperature Measurement] |
Test Standards GMW3172, Nov. 2012, § 8.4.1 Test method Continuous Monitoring during Operating Type 3.2 phases Parameters : Troom, Tmin, Unom |
 |
| 먼지시험 [Dust test] |
Test Standards GMW3172, Nov. 2012, § 9.5.1 Test method Test Duration : 00 hrs |
 |
| 습도내성시험 [Humid Heat Constant] |
Test method During the ON state, Continuous Monitoring is required. During the Sleep/OFF state, continuous parasitic current is monitored and recorded over the 2day test period to detect malfunctions during the test |
 |
| 열충격시험 [Thermal Shock Air-To-Air] |
Test Standards GMW 3431, GMW 3172, Sec 9.4.2 Test method Tmin, Tmax, Cycle 000cycle |
 |
| 온도방치시험 [Storage/ Functional Temperature] |
Test method Place test samples in an environmental chamber. Lower the chamber air temperature to -40 °C, unless otherwise specified in the CTS, at a rate not exceeding 10 °C/minute. |
 |
| 온도측정시험 [Temperature Measurement] |
Test Standards GMW3172/GMW3431 Test method Troom, Tmin, Unom Tpart_max_spec ≥ Tpart + (Tmax ? Tair_ambient) + DM |
 |
| 온습도 특성시험 [Frost Test] |
Test Standards GMW 3172 Test method IEC 60068-2-30, Test Db, Damp heat, cyclic, with the temperature and humidity |
 |
| 복합부식시험 (Cyclic corrosion test-Salt mist) |
Test method Duration: 00 hours Mist level: 0.00 ? 0.00 ml/h on 00 cm2 Number of Cycles: 00 Cycle (00 hours Salt, 00 hours Humidity) Mist level: 0.0 ? 0.0 ml/h on 00 cm2 |
 |
| 고온고습유지시험 (Humid heat constant (HHCO)) |
Test Standards GMW 3172 Test method Temperature (+00 ± 00) °C Duration 00 days Relative Humidity (00 ± 00) % |
 |
| 고온고습시험 (Humid Heat Cyclic (HHC)) |
Test Standards GMW 3172 Test method - Duration: 00 day cycles (total 00 days) - Temperature : +00 °C to +00 °C - Humidity: 00% |
 |
| 고온변화시험 (Temperature Cycle (PTC)) |
Test Standards GMW 3172 Test method Number of PTC cycles : 000 Temperature Range : Tmin to Tmax Temperature Transition Rate : 00 - 00 K/minute |
 |
| 열충격시험 (Thermal Shock Air-To-Air) |
Test Standards GMW 3172 Test method Number of Thermal Shock Cycles : 000 (Function check every 000 cycle) Temperature Range: Tmin to 00 |
 |
| High Temperature Degradation | Test Standards GMW 3172 Test method TRPS / TPH / Tmax and UA for operating type 0.0 / Umin / Umax |
 |
| 작동내구시험
(Durability Reliability test) |
Test Standards GMW 3431 Test method · 00% of the test cycles shall be performed at Tmin · 00% of the test cycles shall be performed at Troom · 00% of the test cycles shall be performed at Tmax |
 |
| 습도유지시험 (Humid Heat Constant) |
Test Standards GMW 3431, IEC 60068-2-38, Test Z/AD, Composite temperature/ humidity cyclic Test method Temperature: (+00±0)℃ , Relative Humidity: (00…00)% Duration: 00 hours |
 |
| 열충격시험 (Thermal shock Air to Air) |
Test Standards GMW 3431, ISO 16750-4, Temperature cycling |
 |
| 온도방치시험 (Storage/functional temp) |
Test Standards GMW 3431, IEC 60068-2-1, Test Ab, Cold |
 |
| 슬립링 습도시험 (Humidity test for slip ring) |
Test Standards MIL-STD-810F, 507.4 Test method 상대습도 : 00℃ +/- 0℃, 습도 : 00% +/- 00% 시간 : 00시간 유지 유지시간 : 00사이클 (상대습도 00% +/- 00% 고정) |
 |
| 열충격시험, 초기고장배제시험 (Cold water shock test) |
Product Optical wave transformer Test Standards According to customer test standards Test method High and Low Temperature Test |
 |
| PCB패널 열충격시험 (Thermal shock test for PCB) |
Product Turn Signal Lamp Test Standards According to customer test standards Test method Temperature (-00℃, 00시간 ~ 00℃, 00시간) |
 |
| 유체저항시험 (Liquid resistance test) |
Test Standards ISO 16750-5 4.7 (table1,2) Test method 제품의 용액에 대한 내유 성능을 평가하기 위한 시험. 해당 유종별 방법 및 방치 시간, 온도에 따른 특성을 평가함 |
 |
| 열 충격 시험 (Thermal Shock Air-To-Air) |
Test Standards GMW 3172 Nov2012 Test method The 00 minute dwell period begins when he component is within 00°C of Tmin or Tmax Functional Status Classification shall be C |
 |
| 고습도시험 (Humid Heat Constant) |
Test method Functional Status Classification shall be A. The parasitic current shall not exceed the required limit or increase by > 00 % from the beginning of this test. Additionally, during the Visual Inspection and Dissection |
 |
| 저온 방치 후 급속수분 형성 시험 (Frost Test) |
Test method 1.2 during cold phase 3.2 during exposure to high humidity. Functional Status Classification shall be A. Additionally, during the Visual inspection and Dissection ? DRBTR, there shall be no evidence of electromigration or dendritic growth. |
 |
| 저온방치 가동시험 (Low Temperature Wakeup) |
Test Standards GMW 3172 Nov2012 Test method Functional Status Classification shall be A Continuous Monitoring during Operating Type 3.2 phases |
 |
| 한계온도검사시험 (Low temperature shock Test) |
Product HV wiring harness Test Standards Renault CDC36-05-009/--L Test method Min temperature : -00 ℃ Duration : 0 hr |
 |
| 고온방치 시험 (High temperature storage Test) |
Test method Max temperature : 00 ℃ Pour ink and water on the top of drum and proceed high temperature storage test. After the test, check whether ink wet passes through the stopper |
 |
| 열충격 시험 [Thermal shock Test] |
Product PCB of Vehicle Control Module Test Standards According to customer’s request Test method Tmin : -00℃ ( 0 hr) / Tmax : 0℃ ( 0 hr) Total 00 cycle |
 |
| 온,습도 시험 [Temperature & Humidity Test] |
Test Standards According to customer’s request Test method Max temperature : 00 Min temperature : -00 Max humidity : 00% Data logging with data logger and can case |
 |
| 온습도 정치 싸이클 시험 [Damp heat Test] | Test method Max temperature : 00 Min temperature : -00 Max humidity : 00% Data logging with data logger, can case and data acquisition equipment |
 |
|
결로시험 [Climatic sequence Test] |
Test Standards IEC 60068-2-38 Z/AD Test method Max temperature : 00 Min temperature : -00 Max humidity : 00% Data logging with data logger |
 |
| 먼지시험 [Dust Test/Solid Tightness Test] |
Test Standards ISO 20653 / GB 4208-2008 Test method Code : IP 0X Dust : Arizona A2 Duration : 00 cycle (00 min per 0 cycle) Data logging with Vecotr can case |
 |
| 열충격 시험 [Thermal shock Test] |
Product Battery Module for Electronic Vehicle Test Standards IEC 60068-2-14 Na Test method Tmin : -00 ℃ ( 0 hr) / Tmax : 00 ℃ ( 0 hr) Total : 00 cycle |
 |
| 저온작동방치시험 [Low Temperature Operation and Exposure Test] |
저온환경에서 방치. 시험 중의 동작정지 및 안전 측으로의 동작 해제는 가능하지만 시험 후 정상동작 할 것. 시험 중 오 동작이 없을 것. 시험 후 데이터 유지기능을 가진 부품은 그 내용에 이상이 없을 것. |
 |
| 먼지시험 [Dust Test / Solid Tightness Test] |
Product Vehicle Interior and Exterior Electronic Device Test method 먼지종류(Arizona Dust, Chalk) 에 따른 시험가능(IPx) |
 |
| 구분 | 세부내용 | |
|---|---|---|
| 진동충격시험 [Mechanical shock] |
Product AAA BBB System Test Standards According to customer request method Test method 00 g 00 ms (X,Y axis only, Total : 00 ) |
 |
| 복합환경진동시험 [Vibration with thermal test] |
Test Standards according to customer request method |
 |
| 진동시험 [Random vibration test] |
Test Standards according to customer request method Test method Vibration & Thermal test (Keep zero compression , filled volume 50%) |
 |
| 진동충격시험 [Mechanical Shock –Collision] |
Test Standards GMW3172, Nov. 2012, § 9.3.3 Test method Acceleration : 000 G Shock Duration : 00 ms Shock Shape : Half Sine |
 |
| 복합환경진동시험 [Vibration with thermal cycling test] |
Test Standards GMW 3431, GMW 3172, 9.3.1.3 Test method Vibration with Thermal Cycling 000 hour each X, Y and Z RMS Acceleration Value = 00.0 (m/s)^2 = 0.00 g |
 |
| 고진폭진동시험 [High Performance Vibration] |
Test Standards According to customer standards Test method |
 |
| 복합환경진동시험 [Vibration under temperature condition] |
Test Standards According to customer standards Test method Troom, Effective Acceleration = 00.00 m/s2 = 1.0 GRMS |
 |
| 운송진동시험 [Shipping Vibration] |
Test Standards GMW 3172 Test method Troom, Effective Acceleration = 00.00 m/s2 = 0.0 GRMS |
 |
| 진동충격시험 [Mechanical shock - collision] |
Test method Acceleration : 00 G Shock Duration : 00 ms Shock Shape : Half Sine Total number of Shocks: 00 in +X / -X Axis 00 in +Y / -Y Axis 00 in +Z / -Z Axis |
 |
| 복합환경진동시험 (Vibration With Thermal Cycling) |
Test Standards GMW 3172 Test method Tmin, Tmax Duration: 00hrs (X-Axis) 00hrs (Y-Axis) 00hrs (Z-Axis) Effective Acceleration = 000m/s2= 00 GRMS |
 |
| Mechanical Shock Pothole |
Test method Troom Acceleration : 00G Shock Duration : 00ms Shock Shape: : Half Sine Total number of Shocks: 000 |
 |
| 진동시험 (Vibration Test) |
Test Standards 고객사요구 시험조건 Test method Z축 00분 진동주파수(00~00Hz) |
 |
| 진동시험 (Vibration Test) |
Test Standards 고객사요구 시험조건 Test method Z축 00분 진동주파수(00~000Hz) |
 |
| 복합환경진동시험 (Vibration with thermal condition) |
Test Standards According to customer request method Test method 00 ~ 000Hz Sweep 진동 온도조건 : 000도 시험시간 : X/Y축 각 00시간, Z축 000시간 |
 |
| 진동시험 (Vibration test) |
Product Motor System Test Standards According to customer request method Test method Random vibration 00~0,000Hz each direction Effective Acceleration : 00.00 Grms |
 |
| 진동내구시험 (Vibration test) |
Product Motor Test Standards According to customer request method Test method Random vibration 00 ~ 0,000Hz each direction Effective Acceleration : 00.00 Grms |
 |
| 진동내구시험 (Vibration test) |
Product Urea tank Test Standards KS R 1034 Test method 진동방향 : X, Y, Z (00.0 Hz, 00Grms) |
 |
| 진동시험 [Vibration test for electronic device] |
Product 방산용 전기배전반 Test Standards According to customer test standards Test method 제시된 진동 조건하에 부품의 내구성 및 성능, 외관의 파손이나 변형유무 등을 관찰하여 제품의 신뢰성을 확보 |
 |
| 진동 충격 시험 (Shock test – Vibration) |
Test Standards MIL-STD-810F, 516.5 Test method Peak acceleration : 00G Duration time : 00ms X+-,Y+-,Z+- 축으로 각각 0회 시험, 총 0회 |
 |
| 진동 및 충격 시험 [Vibration and shock Test] | Product Battery Cell for Electronic Vehicle Test Standards According to customer’s request Test method Vibration : 00 hr of random vibration per 3axis |
 |
| 구분 | 세부내용 | |
|---|---|---|
| 전기특성시험 [Open Circuit – Single Line Interruption] |
Test Standards GMW3172, Nov. 2012, § 9.2.9 Test method Continuous Monitoring |
 |
| 전기특성시험 [Continuous Short Circuit to Battery and to Ground] |
Test method 3.2 (with steady-state loads continuously on, PWM loads at minimum duty cycle for 00 minutes, 00 % duty cycle for 00 minutes and maximum duty cycle for 00 minutes). The following steady-state loads will be : Ua The following PWM loads will be : 00% |
 |
| 전기특성시험 [Intermittent Short Circuit to Battery and to Ground] |
Test method 2.1/3.1/2.2/3.2 (with steady-state loads continuously on, PWM loads at minimum duty cycle for 00 cycles, 00 % duty cycle for 00 cycles and maximum duty cycle for 00cycles) |
 |
| 전기특성시험 [State Change Waveform Characterization] |
Test method All transitions between possible operating types (e.g., 1.2 to 3.2 and 3.2 to 1.2), including internal state changes (e.g., shutdown phase, wakeup phase) |
 |
| 전기특성시험 [Over voltage] |
Test Standards GMW3172, Nov. 2012 Test method All components in the vehicle that have power supplied by the vehicle battery 12 V wiring system |
 |
| 전기시험 [Jump Start] |
Test Standards GMW3172, Nov. 2012, § 8.2.1 Test method Continuous Monitoring Parameters : Inputs to apply the disturbance |
 |
| 전기측정시험 [5-Point Functional/Parametric Check] |
Test method 1. -00C, 00V 2. -00C, 00V 3. 00C ,00V [Operating Type 3.2] 4. 00C, 00V 5. 00C, 00V |
 |
| 전원인가시 온도상승시험 [Temperature Rise - Power On Mode] |
Test Standards GMW 3431, Sec 4.1.4 Test method The operating stabilization temperatures are to be monitored during the measurement |
 |
| 전기특성시험 [Long-term overvoltage] |
Test Standards According to customer request method Test method Continuous Monitoring |
 |
| 전기특성시험 [Slow decrease, quick increase of the supply voltage] |
Test Standards According to customer request method Test method Continuous Monitoring |
 |
| 전기특성시험 [Contact Bounce] |
Test Standards GMW 3431, Sec 4.1.11 Test method OP Mode : 3.2, Continuous Monitoring |
 |
| 전기특성시험 [Isolation Resistance ] |
Test Standards GMW 3431, Sec 4.1.3 Test method Operating Mode : 1.1 / 1.2 |
 |
| 전기특성시험 [Open Circuit Resistance] |
Test Standards GM2 3431, Sec 4.1.2 Test method N/A, Continuous Monitoring |
 |
| 접촉저항측정시험 [Contact Resistance ] |
Test Standards GMW 3431, Sec 4.1.14 Test method Contact Resistance = (Eforward + Ereverse ) / (Iforward + Ireverse) |
 |
| ESD 시험 (ESD Test – Power ON Mode) |
Test Standards GMW3097 Test method EMC test in accordance with ISO 10605 - ESD specification(Ref) Battery voltage - 00 V Temperature & Humidity : 00 ℃ , 00% |
 |
| 접촉저항측정시험 (Contact Resistance Test) |
Test Standards GMW 3431 Test method Dry Circuit Contact Resistance Functional Status Classification shall be A |
 |
| 전원전압 단속시험 (Power Supply Interruptions) |
Test method 10ms, 50ms 주기로 전압을 인가한다. 시험 중의 동작정지 및 안전 측으로의 동작 해제는 가능하지만 시험 후 정상동작 할 것. 시험 중 오 동작이 없을 것. 시험 후 부품 SPEC에 정한 성능을 만족할 것. |
 |
| 절연저항 시험 (Insulation Resistance) |
Test Standards GMW 3172 Nov2012 Test method Functional Status Classification shall be C. The insulation resistance shall be > 10x106 Ω. After the test, perform a 1-Point Functional /Parametric Check. |
 |
| BMS 전기전자 시험 (BMS electronic Test) |
Product BMS Test Standards VW80000 Test method Load dump, Long-term overvoltage, Jump start, Transient overvoltage |
 |
| 과전압시험 [Over Voltage Test] |
시험 중의 동작정지 및 안전 측으로의 동작 해제는 가능하지만 시험 후 정상동작 할 것. 시험 중 오 동작이 없을 것. 시험 후 데이터 유지기능을 가진 부품은 그 내용에 이상이 없을 것. 시험 후 부품 SPEC에 정한 성능을 만족할 것. |
 |
| 전원역극성시험 [Reverse Polarity Test] |
시험 중의 동작정지 및 안전 측으로의 동작 해제는 가능하지만 시험 후 정상동작 할 것. 시험 중 오 동작이 없을 것. 시험 후 데이터 유지기능을 가진 부품은 그 내용에 이상이 없을 것. 시험 후 부품 SPEC에 정한 성능을 만족할 것. |
|
| 표면온도상승시험 [Surface Temperature Rise Test] |
Product Vehicle Gear Shift Control Switch Test method 전압 인가시 시간에 따른 제품표면의 온도변화확인 열전대 및 열화상카메라를 사용하여 온도변화 측정 |
 |
| 전기적 접점 반동시험 [Contact Bounce] | Product : Vehicle Gear Shift Control Switch Monitor the contacts using an oscilloscope, strip chart recorder, or other data acquisition device capable of a minimum sample and storage rate of 40 MHz |
 |
| 구분 | 세부내용 | |
|---|---|---|
| 롤오버시험 [Roll-over simulation] |
Product AAA BBB System Test Standards SAE J2464 |
 |
| 소음시험 [Acoustic test] |
Test Standards SAE J366 |
 |
| Probe Test [Probe test for solid tightness test] |
Test Standards ISO 20653 |
 |
| 염수투과시험 [Seal test] |
Test Standards according to customer request method Test method 5% saline at 0℃ with soluble ultra-violet dye Refer to next page about specific process |
 |
| 복합부식시험 [Salt Fog Test] |
Test Standards According to customer request Test method 10Cycle ? 80 hours |
 |
| Cyclic Corrosion Test [Salt spray with humidity functional endurance test] |
Test method ① Test conditions 1. Salt spray : 00 h, 00 ℃, No humidity 2. Drying : 00 h, 00 ℃, Less than 00 % 3. Temp. and humidity : 00 h, 00 ℃, 00 % ② No. of test cycle : 00 h/per test, Total 00 cycles |
 |
| Mechanical Test [Mechanical Shock Test] |
Test Standards IEC 60068-2-27 Ea Test method ① Shock amplitude : 000 m/s^2 ② Shock duration : 00 msec ③ Test period : 0 shocks in each axes |
 |
| Mechanical Test [Falling tool shocks test] |
Test method ① Test temperature : Troom 00℃, Tmin -00℃ ② No. of test : All plane and one time per surface of specimen. ③ Test method (Drop height : 000mm) A400/50/23 : Striker Type "A", 000g, 00 ℃ A100/50/-30 : Striker Type "A", 000g, -00 ℃ |
 |
| Mechanical Test [Brackets, fasteners resistance test] |
Test Standards Customer standards Test method ① Test temperature : Room temperature (00 degree) ② Test time : 00 times each direction ③ Test direction : each 0 directions(+/-) at 0 points |
 |
| Mechanocal Test [Terminal strength test] |
Test Standards NISSAN 28400NDS00[7] Test method ① Test temperature : Tmin(- 00 ℃), Troom(00 ℃), Tmax(00 ℃) ② Test time and force : 00 times one direction, 000 N.m ③ Test direction : one direction at 00 terminal |
 |
| 용액저항시험 [Fluid corrosion test] |
Test Standards RENAULT D47 1924/--A Test method : According to customer |
 |
| 자유낙하시험 [Free fall test] |
Test method Number of test samples : 00 · Drops per test sample : 00 · Troom · Drop Height : 00 m · Drop Surface: Concrete |
 |
| 용액(설탕)저항시험 [Sugar water function impairment] |
Test Standards GMW3172, Nov. 2012, § 9.5.6 Test method Continuous Monitoring Parameters : Troom |
 |
| 제품하중인가시험 [Crush For Housing –Elbow Load] |
Test Standards |
 |
| 살수시험 [Water test] |
Test Standards GMW3172, Nov. 2012, § 9.5.2 Test method Water Protection Code: 3 |
 |
| 기계적충격시험 [Mechanical overload] |
Test Standards GMW 3431, Sec 4.3.9 Test method N/A , Continuous Monitoring |
 |
| 케이블분리시험 [Connector Retention] |
Test Standards GMW 3431, Sec 4.3.4 Test method N/A , Continuous Monitoring |
 |
| 커넥터 압입시험 [Connector Insertion] |
Test Standards GMW 3431, Sec 4.3.3 Test method N/A , Continuous Monitoring |
 |
| 커넥터 압입/압출시험 [Terminal Retention] |
Test Standards GMW 3431, Sec 4.3.2, GMW3191, Sec 4.2.5 Test method N/A , Continuous Monitoring |
 |
| 소음측정시험 [Audible Sound] |
Test method Sound level checks are to be made using a sound level meter with an oscilloscope output at a point 900 mm from the face of the switch to the face of the microphone. |
 |
| 소음측정시험 [Rattle Evaluation] |
Test method A-weighted sound pressure level Analysis range: 25 Hz to 20 kHz in 1/3 octave band format Measurement duration: 30 seconds in linear octave mode |
 |
| 하중변위측정시험 [Displacement] |
Test Standards GMW 3431, Sec 4.1.6 Test method N/A , Continuous Monitoring |
 |
| 비접촉 3차원 측정 [3D Measuring] |
Test Standards N/A Test method 3D measuring |
 |
| Sugar water function impairment | Test method Sugar water is defined as 000 ml of water with 000 g of sugar fully dissolved. Apply the sugar water onto the component from a distance of 000 cm and wipe away any standing or surface liquid. |
 |
| Crush for Housing Elbow Load |
Test method The component shall be set up to allow testing on all external surfaces with a 00.0 mm or larger diameter area. Subject the component to an evenly distributed 000 N force about any 00.0 mm diameter area for 0.0s |
 |
| 살수시험 [Water Test] |
Product Control SW System for Vehicle Test Standards GMW 3172 Test method ISO 20653 |
 |
| 먼지시험 (Dust test) |
Test Standards GMW 3172 Test method ISO 12103-1, Arizona test dust, A2 fine test dust |
 |
| Rattle 소음시험 (Rattle Evaluation) |
Test method A-weighted sound pressure level Analysis range: 00 Hz to 00 kHz in 1/3 octave band format. Measurement duration: 00 seconds in linear octave mode. |
 |
| 소음측정 시험 (Audible Sound Measurement) |
Test method Sound level checks are to be made using a sound level meter with an oscilloscope output at a point 000 mm from the face of the switch to the face of the microphone. |
 |
| 환경피로반복내구시험 (Fatigue test under temperature condition) |
Test Standards 고객사요구 시험조건 Test method Parking Force : 000N.m , 00.0Hz , 000,000 cycle Drive Force : 000N.m , 00.0Hz , 0,000,000 cycle Temperature range : -00℃~000℃ |
 |
| 용액저항 특성시험 (Fluid Resistance Test) |
Test Standards ISO 16750-5 sec 4.7 Test method Test Code 1 : Spraying Test Code 2 : Brushing Test Code 3 : Wiping Test Code 4 : Pouring |
 |
| 작동소음 시험 (Audible sound) |
Test Standards GMW3431 Sec 4.1.10 Test method Sound level checks are to be made using a sound level meter with an oscilloscope output at a point 900 mm from the face of the switch to the face of the microphone. |
 |
|
스프링 내구시험 [Durability Test] |
Test Standards According to customer request method Test method Parking 000N.m, 00.0Hz, 000,000 cycle Drive 000N.m, 00.0Hz, 0,000,000 cycle Temperature range -00℃~000℃. |
 |
| 차량용모터 복합부식시험 (Salt Spray test for motor) |
Test Standards According to customer test standards Test method Corrosion test 300 hours total (000h + 000h) Functional feature : After 00 cycles After 00 cycles, i.e. a total duration of 000 hours |
 |
| 해저광케이블 벤딩시험 (Bending test for underwater cable) |
Test method Insert a cable sample to cable protector and lay a straight line on plate plane Pull both end side after connect a belt at the end side of a cable that make and keep 2 meter radius, |
 |
| 해저광케이블 슬립시험 (Slip test for underwater cable protector) |
Test method Cable lift to vertical direction after insert a test sample in cable protector with/after bending. Suspend a weight, same as cable protector, to the gravity direction during 1 hour |
 |
| 해저광케이블 추낙하시험 (Drop impact test for underwater cable) |
Test method Height : 00m(1st), 00m(2nd) Impact Type : Free fall drop test) Weight : 000kg Type : Plate layer and vertical bar : 00~00 degree Impact area : bellow 000mm |
 |
| 냉수 충격 시험 (Cold water shock test) |
Function Check/Contact Resistance/ Open Circuit and Isolation Resistance Displacement/Force/Torque to Actuate/ Contact Bounce Rattle/Audible/Storage/ Functional Temperature Thermal Shock/Vibration Test |
 |
| 염수분무시험 (Salt spray test) |
Test Standards Renault D17 1058/H Test method Salt spray 00 Hr 00 ℃ Drying 00 Hr 00 ℃ Humidity 00 Hr 00 % at 00 ℃ |
 |
| 냉수충격 시험 (Cold water shock) |
Test method Max temperature : 00 ℃ Pour ink and water on the top of drum and proceed high temperature storage test. After the test, check whether ink wet passes through the stopper |
 |
| 자유낙하 시험 (Free Fall) |
Test method Minor visible external damage to the component is permitted as long as it does not affect the performance, the attachment interface to the vehicle, or the surfaces visible to the customer. The component shall pass the 5-Point Functional /Parametric Check at the end of the test. |
 |
| 회전 시험 (Roll-over Test) |
Test Standards SAE J2464 Test method Rotate the DUT in 00, 000, 000 degree increments for one full revolution. Data logging with Vector can case |
 |
| 소음평가 시험 (Audible sound Test) |
Product Relay of Battery Pack for Electronic Vehicle Test Standards SAE J366 Test method Sound measurement for both the on-to-of and off-to-on mode of operations |
 |
| 갭측정 시험 (Solid tightness Test) |
Product Battery Pack for Electronic Vehicle Test Standards ISO 20653 Test method Code : IP 00 X |
 |
| 내수성 검사시험(Resistance to hot water Test) | Product HV wiring harness Test Standards ISO 6722 Test method Check withstand voltage and Insulation resistance |
 |
| 비틀림내구 시험 (Torsion durability Test) |
Test Standards According to customer’s request Test method Force : 000Nm Frequency : 0.0HZ Cycle : 00,000,000 |
 |
| 내부식성 시험(Internal corrosion Test) | Test Standards ASTM D1384 Test method Circulate fluid to each sample for internal corrosion test. Duration : 000 hr |
 |
| 기밀 시험(Seal Test) | Test Standards GM 3172, Jul, 2012 Test method Max temperature : 000 ℃ Min temperature : 00 ℃ Place DUT in each chamber with Max and Min temp during 00 min and complete 00 cycle |
 |
| 살수/수밀시험 [Water Test / Liquid Tightness Test] |
Test method Code : IP X00 Water flow rate : 0.0+0.0-0 mm/min Exposure time : 0.0 min Position : Enclosure in 0 fixed positions, inclined by 00° |
 |
| 가스 부식시험 [Gas corrosion Test] |
Product Battery Module for Electronic Vehicle Test Standards IEC 60068-2-60 Ke Test method Method 00 Duration : 00 days |
 |
| 복합부식 시험 [Salt spray with humidity Test] |
Product Specimen of Battery Module for Electronic Vehicle Test Standards IEC 60068-2-11 ka Test method 00 hours spray and 00 hours rest |
 |
| 살수/수밀시험 [Water Test/Liquid Tightness Test] |
Product Vehicle Mechanic System and LED Indicator Test Standards GMW 3172 Nov2012 Test method Water protection code(IPx) |
 |
| 소음측정시험 [Audible Sound] |
Sound level checks are to be made using a sound level meter with an oscilloscope output at a point 900 mm from the face of the switch to the face of the microphone. |
 |
| 시편인장시험 [Tension Test] |
Product Aluminum specimen Test Standards - 고객사 제시기준 Test method 시편을 신장시켜 절단되는 시점에서 기록되는 최대인장응력검출. |
 |
| 구분 | 세부내용 | |
|---|---|---|
| 배터리 진동시험
[Vibration Test] |
MIL STD 810F/ES95400/IEC 60068 |  |
| 배터리 충격시험 [Shock Test] |
Shock Test on 3 direction MIL STD 810F/ES95400/IEC 60068 |
 |
| 배터리 팩 임펙트 시험 [Impact Test] |
Test Standards ISO 20653 |
 |
| 배터리 모듈 가스부식 시험 [Gas Corrosion Test] |
Side and Frontal Impact Test (Customer Internal Standards) |
 |
| 용액 부식 시험 [Chemical Test] |
Chemical Test (Chemical Load Test) ISO 16750-5 |
 |
| KNEE LOAD 시험 [Knee Load Test] |
Chemical Test (Chemical Load Test) ISO 16750-5 |
 |
| Roll Over 시험 [Roll Over Test] |
Knee Load Test ISO 16750-5 |
 |
| Impact (SLED)시험
[SLED Test] |
Impact SLED Test (Customer Internal Standards) |
 |
| 배터리 충방전 시험 [Battery Cyclic Test] |
Charge/DisCharge Test (Customer Internal Standards) |
 |
| 복합 염수부식 시험 [Combined Corrosion Test] |
Combined Corrosion Cyclic Test IEC 60068-2-52 |
 |
| 구분 | 세부내용 |
|---|---|
| 충돌시험 [Crash Test] |
정면충돌시험 / 측면충돌시험 / 후방충돌시험 (Frontal/Side/Rear Crush Test) AEB 개발시험 / Roll Over 시험 (A/BAG Test / Roll Over Test) Lidar, Radar Sensor 개발시험 (Quality Test for Vehicle Sensor) |
| 충격시험 [SLED Test] |
클래쉬패드 충격 안정성 시험 (Crush Pad Impact Test)
DAB/PAB/CAB/SAB/DKAB 등 A/BAG 안정시험 시험(A/BAG Reliability Test) 정면 및 측면 충격시험(Frontal and Far Side SLED Test) |
| A/BAG 전개시험 [A/BAG Test] |
A/BAG 정전개 시험(A/BAG Base Deployment Test)
고속카메라 전개 특성 시험(High Speed Camera Performance Test) |
| 신뢰성 시험 [Reliability Test] |
DAB/PAB/DKAB/IP 진동 특성 시험(Vibration and Environment Test)
ACU 동강성 시험(ACU Dynamic Stiffness and Modal Test) A/BAG 모듈 진동내구 특성 시험(A/BAG Module Life Cycle Test) 열충격 / 낙하 / 온습도싸이클 시험(Thermal Shock, Drop and Temperature Test) |
| 충격시험 [SLED TEST] |
 |
| 구분 | 세부내용 |
|---|---|
| 고가속도 시험 [High Acceleration Test] |
항공기, 유도무기 관련 제품 회전 고가속도 시험 (Aircraft and Missile Parts High G Test)
고가속 피로, 파괴 특성 평가시험(Fatigue and Deformation Function Test) |